Home > Paint & Stains > Wolman >

Wolman DeckStrip ASR 14706

Wolman DeckStrip ASR 14706
Wolman DeckStrip ASR 14706


 
Easily strip hard-to-remove acrylic stain from exterior wood with Rust-Oleum Wolman™ DeckStrip®-ASR Acrylic Stain Remover. This 100% biodegradable formula quickly removes solid or semi-solid deck and siding stains. Just spray on and power-wash off. Professional strength formula - wetting agent, thickener and highest concentration of active ingredient allowable provides maximum stripping power. Safer-to-use than paint strippers – no methylene chloride or caustic chemicals. Easy to use – spray on, rinse off; no scraping or sanding.

Item# Item Name List Price Our Price Qty Add
14706-1 Wolman DeckStrip ASR
$35.14
$31.22
14706-1BOX Wolman DeckStrip ASR - (Box of 4)
Save by the box: $29.29 ea
$140.56
$117.16
Check the items you wish to purchase, then click


Extended Information:
FOR EXTERIOR USE ONLY

Use DeckStrip ASR to strip and restore outdoor wood
decks, fences, siding, shakes and shingles, boat docks &
boardwalks, outdoor furniture & décor, gazebos & arbors, play sets
and more.

WOOD TYPES:

Use on all wood types, including pressure treated
lumber, Cedar, Redwood, exotic hardwoods (Mahogany,
Ipé, Teak, etc.), and North American hardwoods.

Note:
To strip traditional oil or solvent based deck stains, semi-transparent,
toners, tinted wood protectors or sealers, etc. select
Wolman DeckStrip Stain & Finish Remover and use according to
label directions.

Before You Start:
Make sure entire wood surface is dry and free of dust, dirt and debris.
If the surface is hot to the touch or in direct sunlight, dampen with fresh water to cool.
Apply when outside temperatures are above 40°F.
Pre-rinse grass, plants and shrubs surrounding the wood structure to be stripped, then
cover foliage to protect it from exposure to the product. Mask off
siding and cover all wood surfaces not intended to be stripped.
Cover any exposed aluminum surfaces (siding and flashing) to prevent
corrosion. Protect adjacent concrete surfaces from rinse
water. Sweep away surface dirt and debris. Remove any
standing water before beginning application.

Weather Conditions:
For best results, apply when outside temperature is above 50°F
(10°C), and when 24 hours of precipitation-free weather is
expected. Surface to be stripped should be out of direct sunlight
to avoid premature evaporation of the product.

A synthetic bristle brush or mop, pump sprayer or airless sprayer
(with no aluminum parts)is recommended. When working on
vertical surfaces start at the bottom and work to the top of the
structure.
Safe Handling directions must be followed to avoid exposure to
over-spray. (See Handling and Storage section)

CAUTION:
Bare wood and/or coated surfaces can become slippery when wet.
Use caution when walking on wet surfaces.

Prepare to Use:
Moderately shake container, then pour into sprayer tank. If using
a brush or mop, pour product into a 2-1/2 gallon plastic bucket.
Do not mix with any other products.

Apply:
Working on 20 sq. ft. at a time to maintain optimum surface
wetness, apply product and let sit for 15 minutes. If stripper dries
prematurely, keep it wet with additional product as needed.

Rinse
Pressure Wash:  Using a 40° tip and 1,500-2,500 PSI for pressure
-treated wood and hardwood, 500-1,000 PSI for Cedar and
Redwood, pressure-wash the surface to rinse away
dissolved coating. Move lengthwise with boards to
avoid cut marks across grain.  Repeat steps
until entire surface has been stripped. When
finished, rinse surrounding grass and plants thoroughly.

Rinse Brush and Hose: If pressure washing cannot be employed,
vigorously scrub surface with a Wolman WOODWORX® Deck Brush
or other stiff, synthetic, short-bristle broom or brush for several minutes
using moderate pressure. After brushing, rinse thoroughly with a
garden hose,using the highest pressure nozzle setting available.
On a vertical surface, continually rinse stripped areas to avoid
streaking. Rinse any wood fibers off surrounding surfaces
immediately. When dry, surface should appear clean, bright and
free of previous coating. Repeat steps until entire surface has been stripped. When
finished, rinse surrounding grass and plants thoroughly.
Note:
After stripping Cedar, Redwood or exotic hardwoods,
black tannin stains may rise to the surface and give wood an
overall darkened appearance. If this occurs, treat affected areas
with Wolman Deck & Fence Brightener liquid concentrate
to restore the natural wood color. DeckStrip ASR
is not designed to remove tannin bleed stains.

Clean Up:
Clean tools and equipment immediately after use with soap and
water. Use water or vinegar-soaked rag to wipe off any drips or
spills on unintended surfaces immediately.

Safe Handling:
During preparation and application, wear rubber or plastic
coated gloves and safety goggles. If applying with a sprayer,
wear a NIOSH-approved full-face respirator with an organic
vapor cartridge and N-95 pre-filter. Care should be taken to
cover any exposed aluminum surfaces to prevent discoloration, as this
product is corrosive to metal.

DO NOT MIX WITH ANY OTHER PRODUCTS, especially
those containing chlorine or bleach (sodium hypochlorite). Rinse
grass and plants with water after exposure.

Precautions:

DANGER! MAY BE FATAL IF SWALLOWED. CAUSES
SEVERE BURNS. CONTAINS SODIUM HYDROXIDE.
May be harmful if swallowed. Causes eye and skin irritation.
Prevent contact with eyes and skin. During preparation and
application,wear rubber or PVC gloves and safety goggles.
Wash thoroughly after handling. May cause respiratory and
throat irritation. Do not breathe spray mist. If applying with a
sprayer, wear a properly fitted, NIOSH approved respirator.
Use only with adequate ventilation.

KEEP OUT OF REACH OF CHILDREN.





Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Paint & Stains > Wolman
Paint & Stains