Home > Paint & Stains > ZAR >

UGL ZAR Quick Dry Interior Oil-Based Sanding Sealer Polyurethane

UGL ZAR Quick Dry Interior Oil-Based Sanding Sealer Polyurethane
UGL ZAR Quick Dry Interior Oil-Based Sanding Sealer Polyurethane


 
Dries in one hour on bare wood. For floors, furniture, cabinets & woodwork. Ideal as finish coat or undercoating with ZAR Interior Polyurethane. Can also be used as primer to seal bare, open-grained wood before staining.

Item# Item Name List Price Our Price Qty Add
ZAR204-G1 UGL ZAR Quick Dry Interior Oil-Based Sanding Sealer Polyurethane Semi-Gloss Gallon 204
$66.11
$47.99
ZAR204-G1BOX UGL ZAR Quick Dry Interior Oil-Based Sanding Sealer Polyurethane Semi-Gloss Gallon 204 - (Box of 2) Save by the box: $44.79 ea
$132.24
$89.58
Check the items you wish to purchase, then click


Extended Information:
FOR INTERIOR USE ONLY. Do not apply over wood fillers or finishes containing wax or stearates. Do not thin.

COMPOSITION: Oil base
SHEEN: Semi-Gloss 70 ± 3 @ 60º Satin 45 ± 3 @ 60º
% WEIGHT SOLIDS: 40.5 ± 0.5%
% VOLUME SOLIDS: 32.0 ± 0.5%
DENSITY (LBS./US GAL.): 7.2 ± 0.2
VISCOSITY: A - A2 (Gardner Bubble)
pH: N/A
COLORS: N/A

DRY TIME: • 1 Hour Note: Maximum cure and dry time will be prolonged when slightly humid and damp, cool conditions prevail.

CLEAN UP: Paint thinner or mineral spirits Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

COVERAGE (SQ. FT./US GAL.): • 500-600 sq. ft./gal. Note: Actual coverage will vary depending upon application method, surface texture and porosity.

RECOMMENDED FILM THICKNESS/COAT: • 0.5 -1.0 dry mils/coat
FLASH POINT: 104ºF
SHELF LIFE: 5 Years unopened container
FREEZE/THAW: N/A

Do not thin.

New Wood: Sand smooth using fine sandpaper. Wipe using a tack-cloth or cloth dampened with mineral spirits to remove any remnants of dust prior to application and allow to dry. If open-grained woods are to be filled, use a filler that does not contain stearates or waxes such as ZAR Wood Patch or ZAR Trowelable Wood Patch.

Old Clear Finishes in Good Condition : Remove grease, dirt, and wax. Sand lightly in the direction of the grain to remove any gloss. Clean sanding dust with a tack-cloth or cloth dampened with mineral spirtits to remove any remnants of dust prior to application and allow to dry.

Old Clear Finishes in Poor Condition, Lacquer or Shellac: Remove completely. Clean sanding dust with a tack-cloth or cloth dampened with mineral spirtits to remove any remnants of dust prior to application and allow to dry. If the old finish contains wax or stearates, regardless of condition, remove completely. Test ZAR Quick Dry in an inconspicuous area for compatibility.

If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH- approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

Stir thoroughly before and during application. Do not shake! Apply straight from the can. DO NOT THIN. May be applied by brush, pads, lambs wool applicator or spray. Flow ZAR on in the direction of the grain. Sand lightly between coats. Dust and wipe clean. If more than 24 hours elapse between coats, sand thoroughly and clean. Allow first coat to dry 1 hour. Succeeding coats up to 2 hours. Temperature, humidity and film thickness may affect drying time. If while sanding, sandpaper gums or surface feels tacky, extend drying times.

CONTAINS PETROLEUM DISTILLATE. VAPOR HARMFUL. MAY AFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION. Keep away from heat and flame. Prevent build-up of vapors by opening all windows and doors to achieve cross-ventilation.
NOTICE: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Use only with adequate ventilation. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness, or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH approved) during and after application. Follow respirator manufacturer’s directions for respirator use. Do not get in eyes, on skin or clothing. Wash thoroughly after handling.

KEEP OUT OF REACH OF CHILDREN.





Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Paint & Stains > ZAR
Paint & Stains