Total Roof Premium 1-Coat High Solids Silicone Roof Coating is a premium, solvent-free 100% silicone roof coating with unsurpassed waterproofing properties. It’s highly flexible, cures quickly in 2 to 5 hours, and resists the forces of wind-driven rain and snow, ozone, and oxidation. It is unaffected by ponding or standing water. One coat and you are done! Usually requires no primer. Clean it, prep it and coat it! Ideal for any type of aged roof. |
The system provides long-term protection because it resists weathering, aging, oxidation, wind-driven sand, rain and snow, the effects of ozone, ultraviolet radiation and the temperature extremes typically found on roofs. Will not chalk, degrade or haze from UV exposure. Will not wash off if it rains during application. With its high solids content and absence of hydrocarbon solvents, Total Roof 1-Coat High Solids Silicone Roof Coating can be applied in excess of 40 mils in a single coat without blistering, while maintaining maximum adhesion.
This product may contribute toward a variety of LEED credit points.
The high solids white silicone reflects the sun’s UV rays. The roof stays cooler so the interior of the building stays cooler. That means energy savings and more effective HVAC units. Total Roof 1-Coat High Solids Silicone Roof Coating meets “cool roof” requirements and is UL approved.
Composition and Materials: TotalRoof™ 1-Coat High Solids Silicone Roof Coating is a dispersion of silicone rubber. This coating is a one-part, ready-to-use material that can be applied easily to a dry, frost-free surface, and cures at normal temperatures in 2 to 5 hours by reacting with moisture in the air.
Attention Contractors: Let us quote you on your large volume purchases. WE BEAT EVERYONE'S PRICES! Questions? Please call us at 1-800-456-0966
Buy Online & Save with:
☛ FREE SHIPPING² on a pallet!
☛ NO SALES TAX¹
☛ Delivered right to your door or jobsite!
¹ Except FL and NC. ² Continental U.S. Only. Fuel Surcharge and Extended Area Delivery Charges Still Apply. Orders over $4000 may require a wire transfer as payment, we will contact you.
How to Apply:
How to Use TotalRoof™ Premium 1-Coat High Solids Silicone Roof Coating.
It’s simple to use – with just one coat and usually no primer required. Following the steps before coating is essential!
3 Easy Steps:
1. Clean It,
Make sure the roof is dry and clean.
It’s very important that your roof is free of all dust, dirt, debris, oil, solvents and other materials that may adversely affect TotalRoof™ adhesion. You can clean the roof with any of these methods:
Blow-down with compressed air,
Power wash or scrub with stiff bristle or power broom,
Wash down with TSP/water solution to remove oils and grease,
Power vacuum - wet or dry.
Wire brush or brush blast for metal surfaces.
2. Prep It
Examine the roof for any repairs needed before coating.
Patch all cracks, leaks, and seams around vents, stacks and air conditioners with Silicone Seam & Repair Roof Sealant. Seal areas with Silicone Sealant. It’s ready to use and easily applied with a caulk gun and spreader. Ideal for seams, flashing, fasteners and drains.
3. To coat it
you will need:
1 five-gallon can of TotalRoof Premium 1-Coat High Solids Silicone Coating per 400 square feet of roof,
a 9” roller frame and extension pole,
¾” or 1” nap roller cover, paddle to stir coating, mineral spirits and rags for clean-up.
To apply coating:
Stir thoroughly, dip roller in coating or pour product directly on roof.
Apply with overlapping roller strokes.
Coat entire roof.
Let it cure for 2–6 hours.
Coating can be applied in temperatures ranging from 35° to 120°F.
Store any unused coating for up to 36 months. Keep from freezing.