Home > W.F. Taylor >

TUFF-GRIP™ Transitional Pressure Sensitive® (TPS) Vinyl Tile & Rubber Flooring Adhesive

TUFF-GRIP™ Transitional Pressure Sensitive® (TPS) Vinyl Tile & Rubber Flooring Adhesive
TUFF-GRIP™ Transitional Pressure Sensitive® (TPS) Vinyl Tile & Rubber Flooring Adhesive


 
For use with luxury vinyl tile & plank, solid vinyl sheet goods, rubber sheet goods & tile, and vinyl & rubber stair treads. Taylor 2091, with patented Meta-Tec® technology, is an advanced, cross-linking pressure sensitive adhesive featuring high aggressive peel and shear strength. This solvent-free, non-flammable, easy troweling product provides excellent installations for tile-over-tile applications, luxury vinyl tile and plank, solid vinyl tile & plank, vinyl composition tile, homogeneous vinyl sheet goods, and rubber tile & sheet goods over both porous and non-porous surfaces. Taylor 2091 has low odor, and is very quick and easy to use. It demonstrates excellent water and alkali resistance and may be used with confidence over a variety of flooring materials. Plasticizer migration resistance allows installation of a broad variety of vinyl floor products.

Item# Item Name List Price Our Price Qty Add
2091-4 TUFF-GRIP™ Transitional Pressure Sensitive® (TPS) Vinyl Tile & Rubber Flooring Adhesive 4 Gal 2091-4
$219.97
$133.60
2091-1 TUFF-GRIP™ Transitional Pressure Sensitive® (TPS) Vinyl Tile & Rubber Flooring Adhesive Gallon 2091-1
$61.43
$42.94
2091-1BOX TUFF-GRIP™ Transitional Pressure Sensitive® (TPS) Vinyl Tile & Rubber Flooring Adhesive Gallon 2091-1 - (Box of 4)
Save by the box: $40.26 ea
$245.71
$161.04
Check the items you wish to purchase, then click


Extended Information:
USE OVER:
APA registered underlayment grade plywood; terrazzo; existing well adhered tile and sheet goods;
radiant heated subfloors where surface temperatures do not exceed 85°F (29.40°C); and above,
on, or below grade concrete in the absence of hydrostatic pressure, excessive moisture or
alkalinity.
The pH level of concrete must be between 5 and 9 (do not install if over 9) and moisture level
of concrete must beat or below 8 lbs./1000 sq.ft./24 hours (ASTM F-1869) or 90% relative
humidity (ASTM F-2170) for luxury vinyl tile and luxury vinyl plank. For vinyl back sheet goods,
moisture levels must be at or below 5 lbs./1000 sq. ft./24 hours (ASTM F-1869) or 85%
relative humidity (ASTM F-2170. If both tests are performed, the RH test is the qualifying standard.

SUBSTRATE PREPARATION:
Substrate must be sound, smooth, clean, level, dry,and free of dust, dirt, grease, oil, paint,
incompatible curing compounds or sealers, fire retardant chemicals, release agents, or any other
foreign substance that might interfere with a good bond. Subfloor must be smooth and fully adhered.
Subfloor must be structurally sound and smooth. All cracks and depressions must be filled and leveled
with a high quality latex fortified Portland cementitious underlayment according to the instruction of the
underlayment manufacturer. Do not fill expansion joints or other moving joints.

INSTALLATION:
The adhesive, floor covering, and area to receive flooring must be maintained
at a temperature of 65 to5F(18.30 to 35.02C) and at a relative humidity
of 30% to 60% for 72 hours before, during, and after installation. Follow the flooring
manufacturer’s guidelines regarding site conditions and installation.

Porous Surfaces:
May be used either wet or as a pressure sensitive adhesive over porous surfaces. To use wet, apply
adhesive with the recommended trowel and allow to flash off for 5-10 minutes before installing
flooring. Lay tile, plank or sheet goods into wet adhesive according to flooring manufacturer's instructions.
Adhesive must transfer to floor product to ensure proper bond. To use as a pressure sensitive
adhesive, dry to a tacky state and then install flooring according to flooring manufacturer’s instructions
within 3 hours.

Non-Porous Surfaces – Tile & Plank:
Apply with the recommended trowel, allow to dry completely from yellow to tan, and lay in the tile
or plank according to the flooring manufacturers instructions within 3 hours. The highly aggressive
pressure sensitive grip prevents slippage and minimizes seam gaps. Drying time is 45-90 minutes
and will vary depending on temperature and humidity. Installation over areas of incomplete drying
can result in job failure.

Non-Porous Surfaces – Sheet Goods:
Apply with the recommended trowel. When installing sheet goods over non-porous surfaces,
Taylor 2091 must be allowed to set open for up to 30 minutes until dry-to-touch. (Dry-to-touch is tacky but
no transfer to fingers). Time required will vary with ambient conditions. Adhesive must be open enough to
dry on the surface but still allow 100% wet transfer to the back of the sheet goods to ensure proper
adhesion and repositioning.

Coverage:

Over porous substrates
(Vinyl Tile & Plank, Rubber Tile, Vinyl & Rubber Stair Treads): 
Up to 250 sq ft per gallon

Over porous substrates
(Solid Vinyl Sheet Goods, Rubber Sheet Goods):
Up to 350 sq ft per gallon

Over non-porous substrates
(Vinyl Tile & Plank, Rubber Tile, Vinyl & Rubber StairTreads):
Up to 350 sq ft per gallon

Over non-porous substrates
(Solid Vinyl Sheet Goods, Rubber Sheet Goods):
Up to 400 sq ft per gallon







Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

W.F. Taylor
Green Products > Green Paint Sundries
Green Products