Home > Paint & Stains > Seal Krete >

Seal-Krete Clear-Seal Premium Gloss Sealer Gallon 606001

Seal-Krete Clear-Seal Premium Gloss Sealer Gallon 606001
Seal-Krete Clear-Seal Premium Gloss Sealer Gallon 606001

Seal-Krete Clear-Seal Premium Gloss Sealer is a protective top coat for painted, stained or bare concrete.  It extends paint life and is durable, scratch resistant and stain resistant.  Protects against moisture damage and enhances natural color.

Item# Item Name List Price Our Price Qty Add
606001-1 Seal-Krete Clear-Seal Premium Gloss Sealer Gallon
606001-1BOX Seal-Krete Clear-Seal Premium Gloss Sealer Gallon - (Box of 4)
Save by the box: $68.89 ea
Check the items you wish to purchase, then click

Extended Information:
Clear protective finish for painted, stained or bare concrete &
masonry surfaces; premium water-based urethane-fortified acrylic. Available
in Satin & Gloss sheens.

Typical Uses:
Pool Decks
Patios & Porches
Brick & Stone
Driveways & Garages
Exposed Aggregate
Slate & Saltillo
Pavers & Stamped Concrete

Read all directions thoroughly. Recommended: Wear gloves and
safety glasses.
The surface should be clean and dry. You may need
an oil stain remover such as SEAL-KRETE Oil Stain Remover to lift stubborn
oil stains. Pressure-washing is recommended.

Bare Concrete:
Concrete must have cured for a minimum of 30 days.
Etch smooth-fi nished concrete (such as basement or garage fl oors) with a
concrete etching solution like SEAL-KRETE Clean-N-Etch.

If etchingwith muriatic acid the area must be neutralized before proceeding. For
more information visit www.seal-krete.com.

Painted Surfaces:
For use over one-part water-based coatings only;
not recommended over acid-based stains or oil-based coatings. Freshly
painted surfaces must have cured for a minimum of 72 hours. Paint must
be sound (not blistering or peeling). Existing painted surfaces should be
cleaned with a solution of Trisodium Phosphate (TSP) and water. Rinse
well and allow to dry.

Read “LIMITATIONS” section before use. This product is ready
to use; do not dilute. Stir gently; do not shake. Apply in light, even coats. One
coat is recommended; however, over porous surfaces (like saltillo tile) or
when a higher sheen is desired, apply a second coat.

Sealer goes on milky white but dries clear.

Dampen roller, remove excess water, then saturate roller with
product. Keep a wet edge while rolling. Do not allow to puddle, foam or
run. (Use a 1/4” nap for smooth surfaces, 3/8” nap for rough or porous

Pump Sprayer:
Set at a fi ne spray and apply using a circular motion.
To eliminate puddling or to achieve a more uniform fi nish, backroll
immediately after spraying.

150–300 sq.ft. per gallon, depending on surface porosity.

Dry to touch in 1 hour at 77°F (25°C) 50% RH. Recoat in 2 hours.
Dry to foot traffic in 24 hours. Will accept vehicular traffi c in 72 hours. Dry
times should be extended in colder climates.

Clean tools with soap and water immediately after
use. Store in a dry area. KEEP FROM FREEZING.

Clean with a mild soap and water solution. Do not use
solvent-based cleaners.

Temperatures should be 50° to 90°F (10° to 32°C) and should
not fall below 50°F (10°C) within 24 hours of application. Do not apply if rain
is expected within 12 hours. Do not use over acid-based stains, 2-part epoxies
or oil-based paints. Do not use on glazed tile. Do not use in areas subject to
hydrostatic pressure. Smooth-finished concrete may be slippery when wet;
consider using an anti-skid additive like SEAL-KRETE Clear Grip on high foot
traffic areas.

*Sanding or removing paint containing lead may be hazardous. For information
contact the National Lead Information Center at 1-800-424-LEAD or www.

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Paint & Stains > Seal Krete
Paint & Stains