Rust-Oleum Stops Rust Rust Reformer 215215

Rust-Oleum Stops Rust Rust Reformer 215215

Rust-Oleum Stops Rust Rust Reformer

SKU: 215215-1

Each

Regular price $8.86 ea

Save by the box

Regular price $49.86 Box of 6 $8.31 ea

Selected itemsItems: 0

Total: $0.00

Rust-Oleum Stops Rust Rust Reformer instantly converts rust to a non-rusting surface. Apply to rusty metal only. Compatible with most solvent or oil-based paints.

PRODUCT FEATURES:
Indoor/Outdoor
Durable, corrosion-resistant

Apply several light coats a few minutes apart to prevent running and sagging.

This Item Can NOT Be Shipped Internationally

PAINTING CONDITIONS

Use outdoors or in a well ventilated area such as an open garage.
Apply when temperature is between 50-90°F (10-32°C) and humidity is below 65% to ensure proper drying.
Do not apply to surfaces, when heated, exceed 200°F (93°C). Do not apply to galvanized steel. Avoid spraying in
very windy and dusty conditions. Cover surrounding area to protect from spray mist.

SURFACE PREPARATION
Do not use on non-rusted surfaces. Remove all dirt, grease, oil, salt and chemical contaminants by washing
the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to
thoroughly dry. Scrape and wire brush or power tool clean to remove loose rust, scale, and deteriorated coatings.

WARNING! If you scrape, sand or remove old paint from any surface, you may release lead paint dust. LEAD IS
TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE;
ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. For additional
information, contact the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

APPLICATION
Aerosol:
Shake can vigorously for one minute after the mixing ball begins to rattle. Shake often during use. If
mixing ball fails to rattle DO NOT STRIKE CAN. Contact Rust-Oleum. Hold can upright 10-16" from surface and
spray in a steady back-and-forth motion, slightly overlapping each stroke. Keep the can the same distance
from the surface. Keep the can in motion while spraying. The coated surface will turn black. Do not use near open
flame.

Brush:
Stir contents before using. Pour a small amount of Rust Reformer into a separate non-metallic container.
Brush the material evenly across the surface to be coated.The Rust Reformer will dry to a black film in about 15
minutes. Do not return any unused Rust Reformer to the original container. Doing so will contaminate the remaining
material and reduce or eliminate its effectiveness.

DRY & RECOAT
Dry and recoat times are based on 70°F and 50% relative humidity. Allow more time at cooler temperatures.

Aerosol:
Allow to dry for 24 hours. One coat is sufficient. If desired, apply a topcoat after 24 hours.

CLEAN-UP
Aerosol:
When finished spraying, clean valve immediately by turning can upside down and depressing spray button
for 3-5 seconds. Clean up overspray with xylene or mineral spirits. Properly discard empty container. Do not
burn or place in home trash compactor.
Brush:
Spills should be cleaned up immediately with water. Clean brushes and tools with soap and water.

CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a solvent such as mineral spirits. Do not insert any object
into can valve opening.

Rust-Oleum Stops Rust Rust Reformer 215215

Selected itemsItems: 0

Total: $0.00

**Important Note** - You have selected a special order item that requires an extended shipping time. Also note, we cannot verify in stock status until we receive a shipping confirmation from the manufacturer as their stock is constantly changing. All sales are final on special order items, once ordered no changes, cancellations, returns, or refunds can be made, order carefully. By clicking OK below you acknowledge this exception.