Rust-Oleum Marine Topside Paint

Rust-Oleum Marine Topside Paint Quart Gloss Battleship Gray SKU: 207005-E	Each Regular price $30.45 ea	Save by the box Regular price $113.68 Box of 4 $28.42 ea
Rust-Oleum Marine Topside Paint Quart Gloss Black SKU: 207006-E	Each Regular price $30.45 ea	Save by the box Regular price $113.68 Box of 4 $28.42 ea
Rust-Oleum Marine Topside Paint Quart Gloss Bright Red SKU: 207004-BOX-E		Save by the box Regular price $113.68 Box of 4 $28.42 ea
Rust-Oleum Marine Topside Paint Quart Gloss Deep Green SKU: 207007-E	Each Regular price $30.45 ea	Save by the box Regular price $113.68 Box of 4 $28.42 ea
Rust-Oleum Marine Topside Paint Quart Gloss Navy Blue SKU: 207002-E	Each Regular price $30.45 ea	Save by the box Regular price $113.68 Box of 4 $28.42 ea
Rust-Oleum Marine Topside Paint Quart Gloss Oyster White SKU: 207001-BOX-E		Save by the box Regular price $113.68 Box of 4 $28.42 ea
Rust-Oleum Marine Topside Paint Quart Gloss Sand Beige SKU: 207003-BOX-R		Save by the box Regular price $113.74 Box of 4 $28.43 ea
Rust-Oleum Marine Topside Paint Quart Gloss White SKU: 206999-E	Each Regular price $30.45 ea	Save by the box Regular price $113.68 Box of 4 $28.42 ea
Rust-Oleum Marine Topside Paint Quart Semi-Gloss White SKU: 207000-BOX-R		Save by the box Regular price $113.68 Box of 4 $28.42 ea

Selected itemsItems: 0

Total: $0.00

Product variants

SURFACE PREPARATION

Remove all dirt, grease, oil, salt wax and chemical

contaminants by washing the surface with a commercial

detergent or other suitable cleaning method. Rinse with

fresh water and allow to thoroughly dry. Remove loose

paint and rust with a wire brush or sand

paper. Lightly sand glossy surfaces.

WARNING! If you scrape, sand or

remove old paint from any surface, you may release lead

paint dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST

CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN

DAMAGE; ESPECIALLY IN CHILDREN. PREGNANT

WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a

NIOSH approved respirator to control lead exposure.

Clean up carefully with a HEPA vacuum and a wet mop.

Before you start, find out how to protect yourself and your

family by contacting the National Lead Information Hotline at

1-800-424-LEAD or log on to www.epa.gov/lead.

BARE FIBERGLASS

The entire surface, regardless of

age, must be thoroughly washed with a fiberglass

cleaner to remove all traces of mold release agents
and wax. Sand the gel coat with 80-120 grit sandpaper to

create a dull, frosty appearance. Remove

sanding dust and residue.

If the surface is in excellent condition, proceed with

application of the Topside Paint. Rough surfaces or

imperfections should be repaired. Fill all nicks and gouges

with a fiberglass repair compound. Allow to harden and

then sand smooth. Remove sanding dust.

Follow with a coat of Marine Coatings Primer for
Wood & Fiberglass to smooth the surface and provide a
uniform base for the finish coat. Sand smooth

and remove sanding dust.

Proceed with application of the first coat of Topside Paint.

BARE WOOD

Sand the surface smooth with 80-120 grit sandpaper.

Remove sanding dust and residue. Fill all screw heads

or small holes with a wood repair compounds and smooth and

remove sanding dust. Apply one coat of Marine Coatings

Primer for Wood & Fiberglass. Allow to dry four hours and

sand smooth with #150 grit sandpaper.

Repeat Primer application as necessary to achieve

smooth surface. Sand the final coat of Primer

with 220 grit sandpaper then finish with two coats of Topside Paint.

Bare wood that has been repaired or coated with epoxy

must be thoroughly cleaned and then sanded with #120

grit sandpaper. Remove sanding dust.

Follow with a coat of Marine Coatings Primer for Wood & Fiberglass
to smooth the surface and provide a uniform base; sand

smooth and remove sanding dust. Proceed with the first

coat of Topside Paint.

BARE STEEL

Abrasive blast to bare metal or abrade

with emery cloth or abrasive wheel. Immediately apply one

coat of Rust-Oleum Marine Coatings Primer for Metal and

allow to dry for 24 hours. Proceed with the first coat of

Topside Paint. Not for use on galvanized surfaces.

BARE ALUMINUM

Clean surface of grease and oil.

Remove oxidation and abrade the surface with medium

grit emery cloth. Remove sanding dust.

Apply one coat of Rust-Oleum Marine Coatings Primer for Metal
and allow to dry for 24 hours. Proceed with the

first coat of Topside Paint.

PREVIOUSLY PAINTED

Existing paint is in good, sound condition should be cleaned

thoroughly. Sand smooth with #150 grit sandpaper

and remove residue. Proceed with the first coat of Topside Paint.

If the old paint is in poor condition, remove it with a paint and varnish

remover or by sanding.