Minwax Super Fast-Drying Polyurethane for Floors

Minwax Super Fast-Drying Polyurethane for Floors

Minwax Super Fast-Drying Polyurethane for Floors Gloss Gallon

SKU: 13020

Each

Regular price $92.99 ea

Save by the box

Regular price $174.50 Box of 2 $87.25 ea
Minwax Super Fast-Drying Polyurethane for Floors

Minwax Super Fast-Drying Polyurethane for Floors Satin Gallon

SKU: 13022

Each

Regular price $92.99 ea

Save by the box

Regular price $174.50 Box of 2 $87.25 ea
Minwax Super Fast-Drying Polyurethane for Floors

Minwax Super Fast-Drying Polyurethane for Floors Semi-Gloss Gallon

SKU: 13021

Each

Regular price $92.99 ea

Save by the box

Regular price $174.50 Box of 2 $87.25 ea

Selected itemsItems: 0

Total: $0.00

Minwax® Super Fast-Drying Polyurethane for Floors is a durable, protective finish specifically formulated for use on hardwood floors. Minwax® Super Fast-Drying Polyurethane for Floors has a 25% faster recoat time than regular polyurethanes and does not require sanding between coats. Its professional anti-settling formula levels to a smooth, even sheen. A hardwood floor topcoating project can be completed in just one day!
1. Sand floor as appropriate for the type of floor finishing project. Carefully follow label directions and the directions for the sander that you are using.
2. Remove all dust, then thoroughly wipe the floor with a clean cloth dampened with mineral spirits and allow to dry.
3. Before use, stir Minwax® Super Fast-Drying Polyurethane for Floors to rotate the product from the bottom to the top of the can. You will not need to stir again if the project will be completed in one day.
4. Apply a thin coat using a lambswool or synthetic pad applicator, or a natural bristle brush. Maintain a wet edge to avoid lap marks.
5. Let dry at least 3-4 hours until film is no longer tacky to the touch. If allowed to dry for more than 12 hours, sand lightly with 220 grit sandpaper, then wipe floor with a cloth moistened with mineral spirits to remove all dust.
6. Apply a second coat of Minwax® Super Fast-Drying Polyurethane for Floors following steps 4 and 5.
7. If the floor was not stained, apply a third coat of Minwax® Super Fast-Drying Polyurethane for Floors following steps 4 and 5.

Floor will accommodate light foot traffic 24 hours after the final coat of Minwax® Super Fast-Drying Polyurethane for Floors. Avoid heavy traffic and do not replace furniture for 72 hours after the final coat of Minwax® Super Fast-Drying Polyurethane for Floors. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days to allow finish to cure properly. To clean floors protected by Minwax® Super Fast-Drying Polyurethane for Floors, we recommend a gentle cleaner such as Minwax® Hardwood Floor Cleaner.

Clean-up: For easy clean-up, use mineral spirits or paint thinner.

Coverage: Approximately 600-700 sq. ft. per gallon

Note: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Always test surface for tackiness between coats. Do not re-coat when surface is tacky. Slight ambering may be experienced when polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory results.

Minwax Super Fast-Drying Polyurethane for Floors

Selected itemsItems: 0

Total: $0.00

**Important Note** - You have selected a special order item that requires an extended shipping time. Also note, we cannot verify in stock status until we receive a shipping confirmation from the manufacturer as their stock is constantly changing. All sales are final on special order items, once ordered no changes, cancellations, returns, or refunds can be made, order carefully. By clicking OK below you acknowledge this exception.