Home > Paint & Stains > Minwax >

Minwax Oil-Based Clear Protective Finishes

Minwax Oil-Based Clear Protective Finishes
Minwax Oil-Based Clear Protective Finishes


 
Minwax® Fast-Drying Polyurethane is a clear, hard finish that dries fast to protect and beautify interior wood surfaces such as furniture, cabinets, moldings, and doors.  Minwax® Fast-Drying Polyurethane is among the most durable of protective coatings.  Minwax® Fast-Drying Polyurethane’s long-lasting protective finish makes it ideal for use on both finished and unfinished wood.

Item# Item Name List Price Our Price Qty Add
33050 Minwax Oil-Based Clear Protective Finish 11.5 Oz Spray Gloss
$11.42
$9.84
33060 Minwax Oil-Based Clear Protective Finish 11.5 Oz Spray Satin
$11.42
$9.84
33055 Minwax Oil-Based Clear Protective Finish 11.5 Oz Spray Semi-Gloss
$11.42
$9.84
23000 Minwax Oil-Based Clear Protective Finish 1/2 Pint Gloss
$11.84
$9.63
23010 Minwax Oil-Based Clear Protective Finish 1/2 Pint Satin
$11.84
$9.63
23005 Minwax Oil-Based Clear Protective Finish 1/2 Pint Semi-Gloss
$11.84
$9.63
63000 Minwax Oil-Based Clear Protective Finish Quart Gloss
$20.46
$17.73
63010 Minwax Oil-Based Clear Protective Finish Quart Satin
$20.46
$17.73
63005 Minwax Oil-Based Clear Protective Finish Quart Semi-Gloss
$20.46
$17.73
71030 Minwax Oil-Based Clear Protective Finish Gallon Gloss
$56.85
$51.38
71028 Minwax Oil-Based Clear Protective Finish Gallon Satin
$56.85
$51.38
71029 Minwax Oil-Based Clear Protective Finish Gallon Semi-Gloss
$56.85
$51.38
Check the items you wish to purchase, then click


Technical Specs:
DIRECTIONS:

1. Surface must be dry and free of old finishes in poor condition, paint, wax, grease, polish, dirt or other foreign matter.
2. Sand to obtain a smooth uniform surface. Remove all dust with a cloth dampened with mineral spirits.
3. Stir Minwax® Fast-Drying Polyurethane before and during use to eliminate settling on the bottom of the can. Stir in such a manner as to rotate the product from the bottom to the top of the can. NEVER SHAKE.
4. Apply a THIN coat of Minwax® Fast-Drying Polyurethane using a high-quality natural or foam brush.
5. Let dry 4-6 hours. Then lightly sand entire surface with fine sandpaper (220 grit) to ensure an even finish and proper adhesion. Remove all dust.
6. Apply second coat. If third coat is desired, repeat step 5 before application.
7. After final coat, allow 24 hours before light use.

When used on wooden floors, use a lambs wool or synthetic pad applicator or natural bristle brush and maintain a wet edge to avoid lap marks. For maximum durability, we recommend three coats. Avoid heavy traffic and replacing of furniture for 72 hours after final coat. When replacing furniture, do not slide. Do not install rugs or clean floors for 7 days.

CLEAN-UP: For easy clean-up use mineral spirits or paint thinner.

COVERAGE: Approximately 125 square feet per quart.

Note: Above dry times are based on good ventilation, temperature of 77°F and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Always test tackiness between coats. Do not sand or re-coat when surface is tacky. Slight ambering may be experienced when Polyurethane is applied over light-colored wood surfaces. Always spot test on an inconspicuous area to ensure satisfactory


Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Paint & Stains > Minwax
Spray Paint > Stain & Varnish Spray
Paint & Stains
Spray Paint