Home > Paint & Stains > Hammerite Paint and Spray Paint >

Hammerite Rust Cap Smooth Enamel Finish Spray Paint
Hammerite Rust Cap Smooth Enamel Finish Spray
Hammerite Rust Cap Smooth Enamel Finish Spray
 
HAMMERITE RUST CAP SMOOTH ENAMEL FINISH is a self-priming, rust preventive coating designed to provide long-lasting metal protection. It provides a decorative finish that resists corrosion and the damaging effects from moisture and severe weather, and is formulated for interior and exterior use.
   * For use on metal substrates.
   * Can be applied directly over firm, rusty surfaces.
   * For previously painted surfaces, apply HAMMERITE RUST CAP SMOOTH ENAMEL FINISH to a small area first to check adhesion and test for lifting or cracking.
Please note that the manufacturer is discontinuing the entire line of Hammerite products.  Therefore, we can NOT guarantee shipping of the product as it is only available while supplies last.

Item# Item Name List Price Our Price Qty Add
42200 Hammerite Rust Cap Smooth Enamel Finish Spray 12oz Almond
$11.73
$8.95
(Out of Stock)
42200-BOX Hammerite Rust Cap Smooth Enamel Finish Spray 12oz Almond - (Box of 6)
Save by the box: $8.45 ea
$70.38
$50.70
(Out of Stock)
42205 Hammerite Rust Cap Smooth Enamel Finish Spray 12oz Aluminum
$11.73
$8.95
(Out of Stock)
42205-BOX Hammerite Rust Cap Smooth Enamel Finish Spray 12oz Aluminum - (Box of 6)
Save by the box: $8.45 ea
$70.38
$50.70
(Out of Stock)
42230 Hammerite Rust Cap Smooth Enamel Finish Spray 12oz Dark Green
$11.73
$8.95
(Out of Stock)
42230-BOX Hammerite Rust Cap Smooth Enamel Finish Spray 12oz Dark Green - (Box of 6)
Save by the box: $8.45 ea
$70.38
$50.70
(Out of Stock)
Check the items you wish to purchase, then click


Extended Information:
Surface Preparation
  • Prepare surface by removing dirt, grease, wax, moisture, rust, loose paint and any other contamination that can affect the coating's adhesion. If washing is necessary, use a non-soapy detergent or TSP substitute. Rinse well and allow to dry.
  • Scrape off loose paint and rust with a wire brush.
  • Scuff sand rusted, glossy or hard surfaces.

Aerosol Application
  • Use outdoors, or in a well-ventilated area when temperature is between 60°F and 80°F and humidity is below 60% to ensure proper drying. Avoid spraying in very windy or dusty conditions.
  • Shake can vigorously for 2 minutes after mixing ball begins to rattle and often during use. Hold can upright, moving from side-to-side while spraying lightly and evenly about 12” from area being painted. Ensure corners, edges and heavily pitted areas are adequately covered. Apply 3 or more light coats allowing 10 to 15 minutes between coats.

Aerosol Dry Time & Coverage
  • Dries in 15 minutes or less.
  • Handle after one hour.
  • Recoat should be done within 1 hour or after 10 days.
  • A 4 mil coating cures in 14 days.
  • Coverage up to 18 sq. ft.

Aerosol Clean Up & Disposal
  • Clear spray valve immediately after use by turning can upside down and spraying until only clear gas is released.
  • If spray nozzle becomes clogged, remove and clean with mineral spirits. Gently replace spray button with a twisting motion, with top of can and valve opening pointed away from you. Do not stick pins or wire into can opening.
  • Do not dispose of this product down a drain.
  • Please consider donating any unused product.
  • For recycling or disposal information, contact your local household refuse collection service.
Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Paint & Stains > Hammerite Paint and Spray Paint
Paint & Stains