Home > Paint & Stains > Duckback >

Duckback 1 Gal Mason's Select Concrete Etcher 6550

Duckback 1 Gal Mason's Select Concrete Etcher 6550
Duckback 1 Gal Mason's Select Concrete Etcher 6550


 
Duckback Mason's Select Concrete Etcher is a waterborne solution of non-corrosive, low PH organic salts specially formulated to clean and roughen or etch concrete surfaces. Replaces extremely corrosive and hazardous concrete etching products such as muriatic acid and phosphoric acid. Non-corrosive to skin, low-fuming, low odor, biodegradeable and has zero V.O.C. Slightly bodied to cling to non-level surfaces. Removes ground-in dirt, mud and clay. Removes mortar deposits. Approx. 100-200 sq. ft. per gallon.

Item# Item Name List Price Our Price Qty Add
DB-6550-1 Duckback 1 Gal Mason's Select Concrete Etcher 6550
$30.02
$22.92
DB-6550-1BOX Duckback 1 Gal Mason's Select Concrete Etcher 6550 - (Box of 4)
Save by the box: $21.56 ea
$120.08
$86.24
Check the items you wish to purchase, then click


Extended Information:
SURFACE PREPARATION:
If oil and grease stains are present, remove using
Mason’s Select® Concrete Cleaner, following all label
directions for cleaning. Concrete Cleaner will also
neutralize concrete after etching.

APPLICATION:
Apply Concrete Etcher full strength to concrete
surface using a pump-up sprayer, or pour product
directly onto concrete and spread out using a push
broom or brush. Only use synthetic brooms and
brushes. Flood entire surface with Concrete Etcher. A
mild foaming action will indicate that the product is
working. Allow product to remain on surface for a
minimum of 30 minutes. DO NOT ALLOW SOLUTION
TO DRY AT ANY TIME DURING THE ETCHING
PROCESS. Mist surface lightly with water to avoid
solution drying. When foaming action stops, scrub
wet product with a stiff bristle brush broom and rinse
entire area thoroughly with water using a garden
hose or pressure washer. Product may become
slippery once applied, work on small enough areas to
avoid walking on treated surface.

IF STAINING CONCRETE:
If you plan to use a concrete stain or paint, neutralize
the etched surface area using Mason’s Select®
Concrete Cleaner, follow all label directions for
neutralizing. Once concrete is completely dry, inspect
all areas of surface before painting or staining. If
properly etched, the concrete surface will be rough to
the touch (similar to 120 grit sandpaper). Repeat
etching process on any areas that are still smooth or
not sufficiently roughened.

EFFLORESCENCE REMOVAL FROM FIBER CEMENT:
Follow application directions for etching, allowing
product to remain on surface for 10 minutes. Mist
surface lightly with water to avoid solution drying.
Aggressive pressure washing or scrubbing is not
necessary. Rinse surface with water and allow to dry
to determine if efflorescence has been completely
removed. Process may be repeated.

OTHER USES:
For removing ground in dirt and mud stains from
concrete or mortar residue from brick, dilute product
1 part Concrete Etcher to 1 part water. Apply product
with pump-up sprayer, brush, or push broom, then
scrub with bristle brush until clean and rinse with
water or power wash. For removing rust stains from
metal or tarnish from copper & brass, apply product
full strength, multiple applications may be necessary.

APPLICATION TEMPERATURE:
Apply product at temperatures above 50°F. and below 90°F.
Do not apply in direct sunlight if possible.

COVERAGE:
Approx. 100-200 sq.ft. per gallon.

CLEAN UP:
Clean all tools & equipment with water.

SAFE USE & STORAGE:
Do not transfer product into a metal container or
unlabeled container. Store in well-ventilated area.
Keep container tightly closed when not in use.
Keep from freezing.
NOT FOR USE IN SWIMMING POOLS
AS A SHOCK AGENT OR WATER TREATMENT.





Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Paint & Stains > Duckback
Paint & Stains