Wolman RainCoat Clear Water Repellent (Oil Base) Gallon 12386

Wolman RainCoat Clear Water Repellent (Oil Base) Gallon 12386

Wolman RainCoat Clear Water Repellent (Oil Base) Gallon

SKU: 12386-1

Each

Regular price $55.11 ea

Save by the box

Regular price $206.84 Box of 4 $51.71 ea

Selected itemsItems: 0

Total: $0.00

Wolman RainCoat Clear Water Repellent is a totally clear, penetrating oil finish. Prevents water damage. Provides mildew-resistant coating. Immediate application to new pressure-treated wood.
SURFACE PREPARATION

The preparation process outlined below should be followed
to ensure adequate penetration, coloration and optimum
performance of this product.

Perform Splash Test
Step 1

Regardless of whether wood is newly installed or pre-existing, it
is important to determine if there is a surface barrier present
which would prevent the proper penetration or adhesion of a
new coating. To conduct a Splash Test, sprinkle several handfuls
of water on a few distinct areas of the surface. If the water
absorbs rapidly, the surface is ready to be coated. If the water
beads, puddles or is not absorbed, an internal or external barrier
exists, and must be eliminated before coating can begin.

Step 2

Prepare the Surface: Use Wolman DeckBrite™ (Powder Concentrate),
Deck & Fence Brightener (Liquid Concentrate) or DeckStrip®
based on Wood Conditions below.

After preparation, repeat Splash Test to confirm water absorption.

NOTE: Chlorine bleach cleaners alone are not recommended.
These products degrade the wood structure, interfering with
penetration and adhesion of protective coatings.

Wood Condition:

Uncoated, New Wood
If pressure-treated lumber, beading or puddling water may
indicate either a surface barrier such as excess surface wax or
excessive internal moisture content. If new Cedar or Redwood,
“mill glaze” on the surface is likely.  Following the label guidelines,
select the appropriate Wolman surface preparation product
for your particular wood type, either Wolman DeckBrite powder
concentrate or Deck & Fence Brightener liquid concentrate.
Follow usage directions on label, then conduct Splash Test again.
If absorption is not improved, allow wood to dry two weeks in
temperate weather (avg. 70°F, 50% humidity), longer in cooler or
more humid conditions. Test for absorption again before applying
this product.

Uncoated, Weathered Wood
Before coating, weathered wood must be thoroughly cleaned to
remove ground-in dirt, mildew, mold and algae stains, gray, UV
-damaged wood fibers and any other surface contaminants.
According to label guidelines, select the appropriate product for
your particular wood type, either Wolman DeckBrite powder
concentrate or Deck & Fence Brightener liquid concentrate.
Follow usage directions on label, then conduct Splash Test again.

Previously Coated, Weathered Wood
Previous coatings should be removed before application of this
product. If a pigmented oil or latex coating exists, use
Wolman DeckStrip® Stain & Finish Remover according to label
directions to prepare the surface. Acrylic coatings may require a paint
stripper. If coated with a clear sealer or lightly pigmented
finish and little to no pigment remains, Wolman DeckBrite
powder concentrate or Deck & Fence Brightener
liquid concentrate may be used to restore the surface and remove
residual coating/water repellency. Based on label guidelines,
select the appropriate wood cleaner for your particular wood type.

PRODUCT APPLICATION

APPLY ONLY ONE (1) COAT.
DO NOT OVER-APPLY.

Homeowner/DIY’er:

Pump Style Sprayer – The Wolman BackSaver® 2 Gallon
Sprayer is recommended. Back-brush along grain any drips,
runs, uneven coverage or surface puddles.

Brush – Natural or synthetic bristle. Always work from end
to end on a few boards at a time, and maintain a wet edge.

Roller or Stain Pad – Short nap style. When rolling, backbrush
for best results.

Professional Contractor:

Airless Sprayer – Use a 0.009-0.015 inch tip and 100 mesh
filter screen; 250-500 psi. Back-brush along grain any drips,
runs, uneven coverage or puddles.

Before You Start – Replace rotted, extremely weathered or
warped boards. Make sure entire wood surface is dry and free
of dust, dirt and debris. Cover all surrounding areas not
intended to be coated. Do not tint, dilute or mix this product
with any other product.

NOTE:
This product may become cloudy at low temperatures.
To restore clarity, allow to warm, then stir.

CLEAN-UP
Use mineral spirits to clean up over-spray,
drips or spatters on surrounding surfaces, and tools and equipment
after use.

PRECAUTION

DANGER: Rags, steel wool or waste soaked with this product
may spontaneously catch fire if improperly discarded.
Immediately after use, place rags, steel wool, or waste in a
sealed, water filled metal container.

User Tip – “New generation” (non-CCA) pressure-
treated lumber, when initially installed, may develop
pronounced mildew growth during the first few
months of weathering. To reduce or avoid mildew stain
on the coating film and immediately protect against water
damage, pre treat with this product for 6 months or
allow wood to weather for 1 to 3 months before applying
a protective coating product.

Wolman RainCoat Clear Water Repellent (Oil Base) Gallon 12386

Selected itemsItems: 0

Total: $0.00

**Important Note** - You have selected a special order item that requires an extended shipping time. Also note, we cannot verify in stock status until we receive a shipping confirmation from the manufacturer as their stock is constantly changing. All sales are final on special order items, once ordered no changes, cancellations, returns, or refunds can be made, order carefully. By clicking OK below you acknowledge this exception.