Seal-Krete Clear-Seal Concrete Protective Sealer Satin Gallon 604001
|
Seal-Krete Clear-Seal Concrete Protective Sealer Satin Gallon SKU: 604001-E-1 |
Each
Regular price
$45.89 ea
|
Save by the box
Regular price
$172.08 Box of 4
$43.02 ea
|
Clear, urethane-fortified acrylic sealer developed to provide a satin premium finish to painted, stained or bare concrete. It's durable, long-wearing, scratch-resistant, stain-resistant, oil and gas resistant, and it extends paint life. Clear-Seal also protects against moisture damage and enhances the natural color of brick, slate, stone, exposed aggregate, Saltillo, clay pavers, and stamped concrete.
DESCRIPTION:
Clear protective finish for painted, stained or bare concrete &
masonry surfaces; premium water-based urethane-fortifi ed acrylic. Available
in Satin & Gloss sheens.
Typical Uses:
✓
Pool Decks
✓
Patios & Porches
✓
Brick & Stone
✓
Driveways & Garages
✓
Exposed Aggregate
✓
Slate & Saltillo
✓
Pavers & Stamped Concrete
Important:
Read all directions thoroughly. Recommended: Wear gloves and
safety glasses.
SURFACE PREP*:
Note:
The surface should be clean and dry. You may need
an oil stain remover such as SEAL-KRETE Oil Stain Remover to lift stubborn
oil stains. Pressure-washing is recommended.
Bare Concrete:
Concrete must have cured for a minimum of 30 days.
Etch smooth-fi nished concrete (such as basement or garage floors) with a
concrete etching solution like SEAL-KRETE Clean-N-Etch.
Note:
If etching with muriatic acid the area must be neutralized before proceeding. For
more information visit www.seal-krete.com.
Painted Surfaces:
For use over one-part water-based coatings only;
not recommended over acid-based stains or oil-based coatings. Freshly
painted surfaces must have cured for a minimum of 72 hours. Paint must
be sound (not blistering or peeling). Existing painted surfaces should be
cleaned with a solution of Trisodium Phosphate (TSP) and water. Rinse
well and allow to dry.
APPLICATION:
Read “LIMITATIONS” section before use. This product is ready
to use; do not dilute. Stir gently; do not shake. Apply in light, even coats. One
coat is recommended; however, over porous surfaces (like saltillo tile) or
when a higher sheen is desired, apply a second coat.
Note: Sealer goes onmilky white but dries clear.
Roller:
Dampen roller, remove excess water, then saturate roller with
product. Keep a wet edge while rolling. Do not allow to puddle, foam or
run. (Use a 1/4” nap for smooth surfaces, 3/8” nap for rough or porous
surfaces.)
Pump Sprayer:
Set at a fine spray and apply using a circular motion.
To eliminate puddling or to achieve a more uniform finish, backroll
immediately after spraying.
COVERAGE:
150–300 sq.ft. per gallon, depending on surface porosity.
DRY TIME:
Dry to touch in 1 hour at 77°F (25°C) 50% RH. Recoat in 2 hours.
Dry to foot traffic in 24 hours. Will accept vehicular traffic in 72 hours. Dry
times should be extended in colder climates.
CLEAN-UP & STORAGE:
Clean tools with soap and water immediately after use. Store in a dry area. KEEP FROM FREEZING
LIMITATIONS:
*Sanding or removing paint containing lead may be hazardous. For information
MAINTENANCE:
Clean with a mild soap and water solution. Do not use solvent-based cleaners.
LIMITATIONS:
Temperatures should be 50° to 90°F (10° to 32°C) and should
not fall below 50°F (10°C) within 24 hours of application. Do not apply if rain
is expected within 12 hours. Do not use over acid-based stains, 2-part epoxies
or oil-based paints. Do not use on glazed tile. Do not use in areas subject to
hydrostatic pressure. Smooth-finished concrete may be slippery when wet;
consider using an anti-skid additive like SEAL-KRETE Clear Grip on high foot
traffic areas.
*Sanding or removing paint containing lead may be hazardous. For information
contact the National Lead Information Center at 1-800-424-LEAD or www.
epa.gov/lead.