Loctite PL 200 Projects Construction Adhesive
|
Loctite 10 Oz PL 200 Projects Construction Adhesive SKU: 1390603-BOX |
Save by the box
Regular price
$56.28 Box of 12
$4.69 ea
|
||
|
|
Loctite 28 Oz PL 200 Projects Construction Adhesive SKU: 1390602-BOX |
Save by the box
Regular price
$127.68 Box of 12
$10.64 ea
|
||
Loctite PL 200 Projects Construction Adhesive is a premium grade adhesive designed for paneling, drywall and other light construction projects. The low VOC formula can be used both indoors and outdoors. It features a strong, flexible bond and can be used on wood paneling, drywall, and wood or metal studs. Can be used for bonding drywall to: wood, metal studs, concrete or block walls, drywall laminations or paneling and FRP. Reduces nailing and fastener requirements by up to 50%. Can also be used for gap filling. Color: Off-White
Not recommended for:
Bonding panels to metal, plastic, sealed concrete, ceramic tile, painted surfaces and other non-porous substrates
Application to damp surfaces
Underwater applications or permanent water immersion
Applications requiring temperature resistance greater than 170°F (77°C)
Exterior applications where rain is expected within 24 hours
Use on mirrors and metals that will corrode
Bonding polyethylene, polypropylene, nylon or PTFE/Teflon®
Use on Cement Board (Durock®)
Tools Typically Required:
Utility knife, caulking gun
Safety Precautions:
Interior applications require ventilation to the outside during application and cure. Wear gloves. Wash hands after use.
Preparation:
The temperature of the product, the surfaces and the working area must be above 40°F (4°C) and below 100°F (38°C). For best performance, apply adhesive at 70°F (21°C). Ensure surfaces to be bonded are clean, dry, structurally sound and free of dust, grease, oil, and other foreign contaminants. Pre-cut and fit materials before applying adhesive. Cut off tip of cartridge in an “X” cutting method, cutting both sides of the nozzle. Puncture inside seal of cartridge.
Application:
Using a caulking gun, apply a continuous bead of adhesive to all furring strips, studs and top and bottom plates. Position pre-fitted panels. Follow the nailing schedule for adhesives nail-on attachment per the Gypsum Association Manual. If installing panels to drywall, apply adhesive in a zigzag pattern within 1 inch of vertical edges on each side and two vertical beads in the panel centre, 16” apart. Use mechanical fasteners at top and bottom to hold panel in place. Warped or bowed panels should not be used.
Clean-Up:
Clean tools and uncured adhesive residue immediately with warm water and soap. Cured adhesive may be carefully cut away with a sharp-edged tool.
Storage & Disposal:
DAMAGED BY FREEZING. Store in a cool, dry location at room temperature. For maximum shelf life store at 75°F (24°C). Take unwanted product to an approved household hazardous waste transfer facility. Hardened material may be disposed of with trash.
Utility knife, caulking gun
Safety Precautions:
Interior applications require ventilation to the outside during application and cure. Wear gloves. Wash hands after use.
Preparation:
The temperature of the product, the surfaces and the working area must be above 40°F (4°C) and below 100°F (38°C). For best performance, apply adhesive at 70°F (21°C). Ensure surfaces to be bonded are clean, dry, structurally sound and free of dust, grease, oil, and other foreign contaminants. Pre-cut and fit materials before applying adhesive. Cut off tip of cartridge in an “X” cutting method, cutting both sides of the nozzle. Puncture inside seal of cartridge.
Application:
Using a caulking gun, apply a continuous bead of adhesive to all furring strips, studs and top and bottom plates. Position pre-fitted panels. Follow the nailing schedule for adhesives nail-on attachment per the Gypsum Association Manual. If installing panels to drywall, apply adhesive in a zigzag pattern within 1 inch of vertical edges on each side and two vertical beads in the panel centre, 16” apart. Use mechanical fasteners at top and bottom to hold panel in place. Warped or bowed panels should not be used.
Clean-Up:
Clean tools and uncured adhesive residue immediately with warm water and soap. Cured adhesive may be carefully cut away with a sharp-edged tool.
Storage & Disposal:
DAMAGED BY FREEZING. Store in a cool, dry location at room temperature. For maximum shelf life store at 75°F (24°C). Take unwanted product to an approved household hazardous waste transfer facility. Hardened material may be disposed of with trash.