(Your shopping cart is empty)
Search 



 
CHOOSE YOUR
CURRENCY
(not live rates)

Join our mailing list!










  Home > Zinsser >

  Zinsser Binding Peel Stop Primer
  Zinsser Binding Peel Stop Primer
Zinsser Binding Peel Stop Primer


Bookmark and Share
 
PEEL STOP is a clear, flexible bridging sealer for surfaces where peeling, flaking, dusting or chalking is a problem. Use indoors or out to form a breathable membrane over questionable or faulty substrates.

PEEL STOP tightly bonds to old paint and problem areas, forming a sound surface for new paint. PEEL STOP forms a tough acrylic film that stays flexible and helps prevent peeling by letting moisture escape. A clear sealer, PEEL STOP works like nothing else to stop peeling problems on old or new surfaces.

PEEL STOP prevents peeling, blistering, checking, cracking and flaking on wood siding and trim, yellow pine, rough sawn cedar, textured plywood, chalking or powdering, concrete and concrete block, stucco and galvanized gutters.

Peeling paint is usually caused by moisture problems paint fatigue or painting over chalky surfaces.

PEEL STOP can be applied with a brush or roller and cleans up quickly and easily with soap and water.

Item# Item Name List Price Our Price Qty Add
60001-G Zinsser Binding Peel Stop Primer Gallon $32.50 $26.00
60001-GBOX Zinsser Binding Peel Stop Primer Gallon - (Box of 4)
Save by the box: $24.38 ea
$130.00 $97.50
60004-Q-FH Zinsser Binding Peel Stop Primer Quart $11.44 $9.87
60004-QBOX-FH Zinsser Binding Peel Stop Primer Quart - (Box of 6)
Save by the box: $9.38 ea
$68.64 $56.28
Check the items you wish to purchase, then click


Extended Information:
SURFACE PREPARATION
Surfaces should be clean, dry, sound and free of dust, dirt,
excessive chalky material, grime, grease, oil, wax, mildew,
wallpaper adhesive, or any contamination that may
interfere with adhesion. Remove any peeling and/or
unsound coatings and loose fibers with a wire brush or
sandpaper. Sand any remaining paint film edges smooth.
Sand glossy painted areas.

COVERAGE
300-400 sq.ft./gal.(7.4-9.8 m2/l)
depending on application method and surface porosity.

WARNING!
If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.

APPLICATION
Apply only when air, material, and surface temperatures
are between 50-90ºF (10-32ºC) and the relative humidity
is below 85%. Apply with a synthetic (nylon, polyester or
blend) bristle brush, roller, or airless sprayer. Follow
manufacturer's instructions when using spray equipment.
When properly applied, Peel Stop should dry to a slight
sheen. Apply a second coat if dull spots appear. Tinting is
not recommended. Topcoat with any latex or alkyd paint.
To create a more uniform topcoat appearance, prime with
Zinsser Bulls-Eye 1-2-3 Primer or Cover-Stain before
applying topcoat.

LIMITATIONS
Peel Stop is not intended as a substitute for proper
surface preparation or for use on surfaces where paint
failure results from chronic or excessive moisture
intrusion. Peel Stop is not recommended for use on floors,
exterior decks or surfaces subject to immersion or
prolonged contact with water.

DRY TIME
Dries to the touch in 30 minutes and can be primed or
painted in 2 hours. Lower temperatures and higher
humidity can prolong dry time. Allow more time at cooler
temperatures. If conditions do not permit prompt drying,
allow Peel Stop to dry overnight before priming or painting
Do not apply Peel Stop is rain is expected within 8 hours
of priming or topcoating.

CLEAN-UP
Clean up fresh spills and drips with a wet cloth.
Wash application tools in detergent and warm water immediately
after use. Follow equipment manufacturer’s directions to
clean spray equipment. Dispose of unused or unwanted
product in accordance with local laws regulating
water-based coatings.




Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Zinsser