Protect and beautify your interior ceiling surfaces with Valspar® Interior Latex Flat Ceiling paint. This premium quality, fast-drying paint flows on smoothly and evenly, and covers without spattering. The attractive WHITE flat matte appearance provides an elegant finish that is non-yellowing and durable. Valspar Color Center: Color Selector Color Charts Click Here.
- Vehicle Type: Vinyl Acetate
- FINISH: Flat
- NON-SPATTER
- LOW ODOR, LOW VOC
- RECOMMENDED USES:
- Concrete, Masonry, drywall, ceiling tile, and cured plaster,
- Acoustical Ceiling Tile
- TINTING:
- White may be tinted to light and medium
- tints with universal colorants.
- THINNING:
- Not recommended.
- DRYING TIME, @ 77º F, 50% RH:
- Temperature & Humidity Dependent
- Touch: 1 Hour
- Recoat: 2 to 3 hours
- Flash Point: N/A
- VOC: < 100 g/l
- Weight Solids: 53.5 ± 2%
- Volume Solids: 35.6 ± 2%
- Weight Per Gallon: 11.7 Lbs
- COVERAGE: will cover up to 350-400 sq.ft
- @ 4.0 mils wet, 1.3 mils dry
- APPLICATION:
- Apply by brush, roller or airless
- spray (1800-2000PSI and .017-.019 tip).
Surface Preparation
Caulking
Gaps between walls, ceilings, crown
moldings, and other interior trim can
be filled with the appropriate caulk
after priming the surface.
Drywall
Fill cracks and holes with patching
paste / spackle and sand smooth.
Joint compounds must be cured and
sanded smooth. Remove all sanding
dust.
Plaster
Bare plaster must be cured and hard.
Textured, soft, porous, or powdery
plaster should be treated with a solution
of 1 pint household vinegar to 1
gallon of water. Repeat until the surface
is hard, rinse with clear water and
allow to dry.
Masonry, Concrete, Cement, Block
All new surfaces must be cured according
to the supplier’s recommendations
usually about 30 days. Remove
all form release and curing agents.
Rough surfaces can be filled to provide
a smooth surface. If painting
cannot wait 30 days, allow the surface
to cure 7 days.
Wood
Sand any exposed wood to a fresh
surface. Patch all holes and imperfections
with a wood filler or putty and
sand smooth.
Mildew
Remove before painting by washing
with a solution of 1 part liquid bleach
and 3 parts water. Apply the solution
and scrub the mildewed area. Allow
the solution to remain on the mildewed
area for 10 minutes. Rinse thoroughly
with water and allow the surface to dry
prior to painting. Wear protective
eyewear, waterproof gloves, and protective
clothing. Quickly wash off any
mixture that comes in contact with
your skin. Do not add detergents or
ammonia to the bleach water solution.
Cleanup Information
Clean spills and spatters immediately
with soap and warm water. Clean
hands and tools immediately after use
with soap and warm water. After
cleaning, flush spray equipment with
mineral spirits to prevent rusting of the
equipment. Follow manufacturer’s
safety recommendations when using
mineral sprits.
Warning! Removal of old paint by
sanding, scraping or other means may
generate dust or fumes that contain
lead. Exposure to lead dust or fumes
may cause brain damage or other
adverse affects, especially in children
or pregnant women. Controlling exposure
to lead or other hazardous substances
requires the use of proper
protective equipment, such as a properly
fitted respirator (NIOSH approved)
and proper containment and cleanup.
For more information, call the National
Lead Information Center at 1-800-424-
LEAD (in US) or contact your local
health authority.
|
