Minwax Polycrylic Protective Finish

Home > Minwax >

Minwax® Polycrylic® Protective Finish is a crystal clear, fast-drying protective topcoat for use over bare wood, oil- and water-based stains, paint and wallpaper. It has very little odor, is non-flammable, cleans up easily with soap and water, and can be recoated in only 2 hours. Minwax® Polycrylic® resists damage from abrasion, scuffing, chipping, water, alcohol and other common household chemicals.
Minwax® Polycrylic® is not recommended for use on floors.

Item#	Item Name	List Price	Our Price	Qty	Add
65555	Minwax Polycrylic Protective Finish Quart Gloss	$22.89	$19.05
63333	Minwax Polycrylic Protective Finish Quart Satin	$22.89	$19.05
64444	Minwax Polycrylic Protective Finish Quart Semi-Gloss	$22.89	$19.05
15555	Minwax Polycrylic Protective Finish Gallon Gloss	$64.30	$53.59
13333	Minwax Polycrylic Protective Finish Gallon Satin	$64.30	$53.59
14444	Minwax Polycrylic Protective Finish Gallon Semi-Gloss	$64.30	$53.59
Check the items you wish to purchase, then click

Technical Specs:

1. Surface must be dry and free of wax, grease, polish, old finishes in poor condition or any foreign matter.
2. Sand to a smooth, uniform surface. DO NOT USE STEEL WOOL. Remove dust with a cloth dampened with water or mineral spirits. Let dry completely.
3. If desired, apply Minwax® Wood Finish™ or Minwax® Water-Based Wood Stain to unfinished interior wood surfaces following label directions. Wait at least 24 hours before applying Polycrylic® over Minwax® Wood Finish™.
4. Stir well before and regularly during use. DO NOT SHAKE. FINISH APPEARS MILKY IN CAN BUT DRIES CRYSTAL CLEAR.
5. Apply a thin coat of Polycrylic® with a high-quality synthetic bristle brush. Apply in one direction with the grain. Do not overbrush.
6. Let dry at least 2 hours then sand with very fine sandpaper (220 grit) to ensure an even finish and proper adhesion of additional coats. Do not use steel wool. Remove all dust.
7. Apply second coat. For additional coats, repeat Step 6 before applying. Three coats are recommended.
8. After final coat, allow 3 hours before light handling and 24 hours before normal use.
Special Instructions: Polycrylic® should not be applied over red mahogany stain. Instead, use Minwax® Fast-Drying Polyurethane over any red mahogany stain.
Clean Up: Clean with soap and warm water immediately after use.
Coverage: Approximately 125 sq. ft. per quart
Notes: Thinning is not recommended. Keep from freezing. Store below 105°F. For interior use only. Dry times are based on good ventilation, temperature of 77°F, and 50% relative humidity. Lower temperature, higher humidity, lack of air movement or application of thick coats will extend drying times. Always test surface for tackiness between coats. Oil-based stains, paints or coatings applied under Polycrylic® may amber normally. Always spot test on an inconspicuous area to ensure satisfactory results.

Share your knowledge of this product with other customers... Be the first to write a review.

Browse for more products in the same category as this item:

Minwax

	ASM Zip-Spray 3100 Plus Airless Paint Sprayer by Graco $3,378.75
	Wooster Tray Liner
	OLFA Extra Heavy-Duty Snap-off Blade, 5-pack (HB-5B)